Waste Tyre Chemical Recycling廃タイヤ ケミカルリサイクル

Journal of Industrial Resource Circulation産業資源循環学会誌
Vol.07 / 04第07 巻 / 04 号2026pp.112–121頁112–121DOI10.48219/jirc.2026.0704.112
Original Research · Chemical Recycling原著論文 · ケミカルリサイクル

Waste Tyre Chemical Recycling: An Oxygen-Limited Pyrolysis Route for Recovering Oil, Carbon and Steel from End-of-Life Tyres廃タイヤ ケミカルリサイクル ─ 酸素制限下の乾留熱分解による再生油・再生カーボンブラック・再生スチールの回収

Abstract要旨

End-of-life tyres are a bulky, non-decomposing composite of oil-derived polymer, carbon and steel that continues to be generated wherever vehicles operate. This paper describes an integrated pyrolysis line in which prepared tyres are thermally decomposed under oxygen-limited conditions and separated into three material streams — regenerated oil (450–500 L / t), recovered carbon (300–330 kg / t) and recovered steel (140–150 kg / t). Non-condensable gas is fed back into process heating and, where the configuration permits, into on-site power generation, reducing external energy demand. Under the source calculation basis, CO2 emissions per tonne of feedstock fall from 2.92 t (incineration) to 0.36 t (this system), corresponding to a reduction of approximately 88%.

The route treats tyres as a manufactured composite carrying residual industrial value rather than as terminal waste. Sealed, negatively-pressurised construction limits release of process gas and odour, while temperature and pressure instrumentation isolates non-nominal conditions at the section level. Standardised measurement of yield, energy balance and downstream reuse is presented as the basis for continued improvement across installations.

使用済みタイヤは、石油由来のポリマー・カーボン・スチールからなる、かさばり自然分解しない複合材料であり、車両が使用される限り発生し続ける。本稿では、前処理したタイヤを酸素制限下で乾留熱分解し、再生油(450–500 L / トン)、再生カーボンブラック(300–330 kg / トン)、再生スチール(140–150 kg / トン)の3つの材料へ分離回収する一連の乾留熱分解ラインについて述べる。工程で発生する不凝縮ガスは、加熱燃料および設備構成に応じて発電に利用され、外部からのエネルギー供給を低減する。元資料の算定条件において、原料1トンあたりのCO2排出量は焼却処理の2.92トンから本方式の0.36トンへと減少し、約88%の削減に相当する。

本方式は、タイヤを終末廃棄物ではなく、なお産業的価値を持つ製造複合材として扱う。密閉・負圧の構造により工程ガスと臭気の外部への洩しを抑制し、温度・圧力の計装を通じて遡行時には当該区間を切り離す。回収量・エネルギー収支・利用先の標準化された測定を、導入サイトごとの改善の基盤として位置づける。

Keywords pyrolysis · end-of-life tyres · resource circulation · carbon black · CO₂ reduction · industrial reuse
キーワード 乾留熱分解 · 使用済みタイヤ · 資源循環 · カーボンブラック · CO₂削減 · 産業利用

1Introduction序論 · 課題の所在

Stockpiled end-of-life tyres.
Fig. 1図 1Stockpiled end-of-life tyres. Continuous generation, bulk volume and a non-decomposing composite profile make disposal a standing rather than a one-off problem.野積みされた使用済みタイヤ。継続的に発生し、かさばり自然分解しないため、廃棄は一時的な問題ではなく恒常的な課題となる。

Tyres are consumed wherever vehicles are used, so end-of-life tyres are generated continuously and in volume. They are bulky and do not decompose, and long-term stockpiling brings fire and environmental risk.

タイヤは車両が使われる限り消費されるため、使用済みタイヤは継続的かつ大量に発生する。かさばる上に自然分解せず、長期間にわたる野積みは火災・環境面のリスクを伴う。

Because a tyre is a manufactured composite of oil-derived polymer, carbon and steel, disposal also means discarding material that still holds industrial value. Suitable treatment and resource circulation are therefore practical requirements — not an abstract ideal.

タイヤは石油由来原料・カーボン・スチールを組み合わせて製造された複合製品であり、廃棄はすなわち産業的価値をなお保持する材料を失うことを意味する。適正な処理と資源循環は理念ではなく、実務上の要請である。

2Pyrolysis Process乾留熱分解プロセス

Prepared tyres are heated in the absence of sufficient oxygen, so the material decomposes into a vapour stream rather than burning. The vapour is separated, cooled and condensed into oil 450–500 L/t; solid and metal fractions are recovered separately as carbon 300–330 kg/t and steel wire 140–150 kg/t.

前処理したタイヤを酸素が十分に存在しない状態で加熱することにより、材料は燃焼せずに分解し、蒸気(ガス)として取り出される。この蒸気を分離・冷却・凝縮して油 450–500 L/t とし、固形分・金属分はそれぞれカーボン 300–330 kg/t 、スチールワイヤ 140–150 kg/t として別に回収する。

01 · FEED01 · 装填
Feeding原料装填
Prepared tyres are loaded into the reactor as the feedstock stream.前処理済のタイヤを原料として反応器へ装填する。
02 · REACT02 · 反応
Pyrolysis熱分解
Oxygen-limited thermal decomposition drives the material to a vapour phase.酸素制限下で加熱し、材料を蒸気(ガス)へ分解する。
03 · COOL03 · 冷却
Cooling & Condensing冷却・凝縮
Vapour is cooled and condensed into a liquid oil fraction.蒸気を冷却・凝縮させ、液状の油分として取り出す。
04 · SEP04 · 分離
Separation分離
Oil, carbon and steel fractions are isolated per stream.油・カーボン・スチールを系統別に分離する。
05 · STORE05 · 貯蔵
Storage貯蔵
Recovered streams are routed to dedicated storage.回収物を専用の貯蔵設備へ送る。
Fig. 2図 2Process flow of oxygen-limited pyrolysis. Feeding → reaction → cooling → separation → storage are managed as a single line under central instrumentation.酸素制限下の乾留熱分解プロセス。装填 → 反応 → 冷却 → 分離 → 貯蔵を一系統として、中心制御下に一括管理する。

3Recovered Resources回収物の内訳

Three material streams are recovered per tonne of feedstock. Yield ranges are indicative reference values taken from the source material and vary with feedstock, operating conditions and plant configuration.

原料1トンあたり、3つの材料を回収する。回収量の範囲は元資料に基づく参考値であり、原料・運転条件・設備構成によって変動する。

Stream回収物Yield / tonne回収量 / トンIndustrial destination主な利用先
Regenerated Oil再生油450–500 LLiquid fuel fraction液状の燃料留分
Recovered Carbon再生カーボンブラック300–330 kgIndustrial solids reuse産業用途への固形分再利用
Recovered Steel再生スチール140–150 kgSteel input (bead / belt wire)製鉄原料(ビード・ベルト部)
Mass composition質量構成per 1,000 kg feedstock原料 1,000 kg あたり
Regenerated Oil再生油≈ 390 kg
Recovered Carbon再生カーボンブラック315 kg
Recovered Steel再生スチール145 kg
Gas / lossガス・ロス150 kg

4Plant Engineeringプラント構成

Pyrolysis plant equipment — reaction vessels, piping and instrumentation.
Fig. 3図 3Pyrolysis plant equipment. Reaction vessels, piping and instrumentation are assembled as one line; feeding, pyrolysis, cooling and separation are managed as a single process.乾留熱分解プラントの設備。反応容器・配管・計装機器を一つの系統として組み上げ、装填・熱分解・冷却・分離を一連の工程として管理する。

The plant links feeding, pyrolysis, cooling, separation and storage into a single managed flow. A control system supervises temperature and pressure across the line, supported by shut-off valves, backflow prevention and combustion treatment of surplus gas.

プラントは、原料の装填・熱分解・冷却・分離・貯蔵を一連の工程として連結し管理する。制御盤が工程全体の温度・圧力を監視し、遮断弁・逆流防止機構・余剰ガスの燃焼処理設備がこれを支える構成としている。

i · Heat-Resistant Constructioni · 熱に耐える構造
Materials are selected to withstand repeated heating and cooling cycles, with maintainability and service life taken into account.繰り返しの加熱と冷却に対応するため、耐熱性を備えた材料を使用する。設備の耐久性・保守性に配慮した設計である。
ii · Sealing & Pressure Controlii · 密閉と圧力の管理
Sealed construction under negative-pressure control limits release of process gas and odour outside the plant boundary.密閉構造と負圧制御により、処理中に発生するガスや臭気の外部への漏出を抑える設計を採用している。
iii · Monitoring & Safety Responseiii · 運転状態の監視
Temperature and pressure sensors with automatic control track each stage; deviations trigger flow isolation via safety mechanisms.温度・圧力センサーと自動制御を組み合わせ、各工程の状態を把握する。異常時には安全機構によって流路の遮断などを行う。

5Energy Utilisationエネルギーの活用

Pyrolysis produces a gas fraction that does not condense into oil. Part of that gas is used as fuel for process heating and, where the configuration allows, for on-site power generation — reducing energy the plant must draw from outside.

熱分解では、油として凝縮しないガス分が生じる。このガスの一部を工程の加熱用燃料として、さらに設備構成に応じて発電にも活用することで、外部から供給するエネルギーの低減を図る。

Source発生源
Non-condensable gas不凝縮ガス
→
Use A用途 A
Process heating工程の加熱燃料
→
Use B · Outcome用途 B · 成果
Power generation発電・購入電力の低減
Note注

The share of gas available for heating or generation depends on plant design, load and operating conditions, and is determined for each installation.

加熱や発電に利用できるガスの割合は、設備設計・負荷・運転条件によって異なり、導入ごとに確認すべき項目である。

6Environmental Performance環境性能

By recovering material and reusing the process gas, the system targets a lower-carbon route than incineration of the same feedstock. Reference figures below follow the source calculation basis; actual reduction depends on processing conditions, electricity mix, comparison basis and system boundary.

廃タイヤの再資源化と、処理工程で発生するガスの活用を通じて、従来の焼却処理と比較したCO₂排出量の削減を目指す。以下は元資料の算定条件に基づく参考値であり、実際の削減効果は処理条件、使用電力、比較対象、システム境界等によって異なる。

CO₂ emissions · per tonne of waste tyresCO₂排出量 · 廃タイヤ 1 トンあたりt-CO₂ / t
Conventional incineration従来の焼却処理
2.92t
This system本システム
0.36t
Reduction under the source calculation basis元資料の算定条件における削減率≈ 88%

7Circular Resource Model資源循環モデル

Chemical recycling does not end at treatment. Each recovered stream needs a defined industrial destination, and throughput and operating data are recorded so that recovery yield and environmental performance can be tracked over time.

ケミカルリサイクルは処理で完結しない。回収した油・カーボン・鉄それぞれに産業側の利用先を定め、処理量や稼働状況を記録することで、資源回収量と環境負荷の低減効果を継続的に把握する。

01
Waste Tyres廃タイヤ
End-of-life tyres are collected as feedstock rather than discarded.使用済みタイヤを廃棄物ではなく原料として回収する。
02
Resource Recovery資源回収
Thermal decomposition separates the tyre into recoverable streams.熱分解により、回収可能な素材ごとに分離する。
03
Oil · Carbon · Steel再生油・カーボン・鉄
Three recovered streams, each with its own industrial destination.3つの回収物それぞれに、産業側の利用先を定める。
04
Industrial Reuse産業での再利用
Returned as fuel, industrial feedstock and steel input — the cycle continues.燃料・産業原料・製鉄原料として産業へ戻し、循環が続く。

8Conclusion結論

An integrated pyrolysis line converts a bulky, non-decomposing waste stream into three defined material streams under sealed, negatively-pressurised, instrumented conditions. Process gas is fed back into heating and generation, and the resulting CO₂ profile is materially below the incineration baseline under the source calculation basis. Continued improvement rests on standardised measurement of yield, energy balance and downstream reuse for each installation, rather than on abstract commitment.

本方式は、かさばり自然分解しない廃タイヤを、密閉・負圧・計装管理下の一連工程によって 3 系統の材料へ変換する。工程内で発生するガスを加熱・発電へ再利用し、元資料の算定条件においてはCO₂排出量が焼却基準を大幅に下回る。今後の改善は、抽象的な言明ではなく、導入サイトごとの回収量・エネルギー収支・再利用先に関する標準化された測定にに基づくべきである。